|-help||Prints a short summary of the p options and exists.|
|-version||Print version information and exit.|
Set the SCSI target for the CD/DVD/BluRay-Recorder, see notes above.
A typical target device specification is
If a filename must be provided together with the numerical target
specification, the filename is implementation specific.
The correct filename in this case can be found in the system specific
manuals of the target operating system.
FreeBSD system without
CAM support, you need to use the control device (e.g.
/dev/rcd0.ctl). A correct device specification in this case may be
General SCSI addressing
Remote SCSI addressing
Alternate SCSI transports
To access SCSI devices via alternate transport layers, you need to prepend the SCSI device name by a transport layer indicator. The transport layer indicator may be something like USCSI: or ATAPI:. To get a list of supported transport layers for your platform, use dev= HELP:
Scsibus 0 is the default SCSI bus on the machine. Watch the boot messages for more information or look into /var/run/dmesg.boot for more information about the SCSI configuration of your machine. If you have problems to figure out what values for scsibus,target,lun should be used, try the -scanbus option of btcflash described below.
Using logical names for devices
If a file /usr/local/etc/cdrecord exists, and if the argument to the dev= option or the CDR_DEVICE environment does not contain the characters ,, /, @ or :, it is interpreted as a device label name that was defined in the file /usr/local/etc/cdrecord (see FILES section).
|Set the default SCSI command timeout value to #seconds. The default SCSI command timeout is the minimum timeout used for sending SCSI commands. If a SCSI command fails due to a timeout, you may try to raise the default SCSI command timeout above the timeout value of the failed command. If the command runs correctly with a raised command timeout, please report the better timeout value and the corresponding command to the author of the program. If no timeout option is present, a default timeout of 40 seconds is used.|
|Set the misc debug value to # (with debug=#) or increment the misc debug level by one (with -d). If you specify -dd, this equals to debug=2. This may help to find problems while opening a driver for libscg. as well as with sector sizes and sector types. Using -debug slows down the process and may be the reason for a buffer underrun.|
|Tell the scg-driver to modify the kernel debug value while SCSI commands are running.|
|Do not print out a status report for failed SCSI commands.|
|-v||Increment the level of general verbosity by one. This is used e.g. to display the progress of the process.|
|-V||Increment the verbose level with respect of SCSI command transport by one. This helps to debug problems during the process, that occur in the CD-Recorder. If you get incomprehensible error messages you should use this flag to get more detailed output. -VV will show data buffer content in addition. Using -V or -VV slows down the process.|
|Specify the filename where the firmware should be read from.|
|-scanbus||Scan all SCSI devices on all SCSI busses and print the inquiry strings. This option may be used to find SCSI address of the devices on a system. The numbers printed out as labels are computed by: bus * 100 + target|
Set the maximum transfer size for a single SCSI command to #.
The syntax for the
ts= option is the same as for cdrecord fs=# or sdd bs=#.
If no ts= option has been specified, btcflash defaults to a transfer size of 256 kB. If libscg gets lower values from the operating system, the value is reduced to the maximum value that is possible with the current operating system. Sometimes, it may help to further reduce the transfer size or to enhance it, but note that it may take a long time to find a better value by experimenting with the ts= option.
RSH If the RSH environment is present, the remote connection will not be created via rcmd(3) but by calling the program pointed to by RSH. Use e.g. RSH=/usr/bin/ssh to create a secure shell connection.
Note that this forces cdrecord to create a pipe to the rsh(1) program and disallows cdrecord to directly access the network socket to the remote server. This makes it impossible to set up performance parameters and slows down the connection compared to a root initiated rcmd(3) connection.
RSCSI If the RSCSI environment is present, the remote SCSI server will not be the program /usr/local/sbin/rscsi but the program pointed to by RSCSI. Note that the remote SCSI server program name will be ignored if you log in using an account that has been created with a remote SCSI server program as login shell.
A typical error message for a SCSI command looks like:
The first line gives information about the transport of the command. The text after the first colon gives the error text for the system call from the view of the kernel. It usually is: I/O error unless other problems happen. The next words contain a short description for the SCSI command that fails. The rest of the line tells you if there were any problems for the transport of the command over the SCSI bus. fatal error means that it was not possible to transport the command (i.e. no device present at the requested SCSI address).btcflash: I/O error. test unit ready: scsi sendcmd: no error CDB: 00 20 00 00 00 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 25 00 00 00 00 00 Sense Key: 0x5 Illegal Request, Segment 0 Sense Code: 0x25 Qual 0x00 (logical unit not supported) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 0.002s timeout 40s
The second line prints the SCSI command descriptor block for the failed command.
The third line gives information on the SCSI status code returned by the command, if the transport of the command succeeds. This is error information from the SCSI device.
The fourth line is a hex dump of the auto request sense information for the command.
The fifth line is the error text for the sense key if available, followed by the segment number that is only valid if the command was a copy command. If the error message is not directly related to the current command, the text deferred error is appended.
The sixth line is the error text for the sense code and the sense qualifier if available. If the type of the device is known, the sense data is decoded from tables in scsierrs.c. The text is followed by the error value for a field replaceable unit.
The seventh line prints the block number that is related to the failed command and text for several error flags. The block number may not be valid.
The eight line reports the timeout set up for this command and the time that the command really needed to complete.
J..org Schilling Seestr. 110 D-13353 Berlin Germany
Additional information can be found on:
If you have support questions, send them to:
If you have definitely found a bug, send a mail to:
To subscribe, use:
|J*org Schilling||BTCFLASH (1L)||2014/12/03|