Manual Reference Pages - GRDLANDMASK (1)
grdlandmask - Create "wet-dry" mask grid file from shoreline data base.
Grid File Formats
grdlandmask -Gmask_grd_file] -Ixinc[unit][=|+][/yinc[unit][=|+]] -Rwest/east/south/north[r] [ -Amin_area[/min_level/max_level][+r|l][ppercent] ]
[ -Dresolution[+] ] [ -F ] [ -Nmaskvalues[o] ]
[ -V ]
grdlandmask reads the selected shoreline database and uses that information to decide which
nodes in the specified grid are over land or over water. The nodes defined by
the selected region and lattice spacing will be set according to one of two criteria:
(1) land vs water, or (2) the more detailed (hierarchical) ocean vs land vs lake vs island vs pond. The
resulting mask may be used in subsequent operations involving grdmath to mask out
data from land [or water] areas.
Name of resulting output mask grid file.
(See GRID FILE FORMATS below).
x_inc [and optionally y_inc] is the grid spacing. Optionally, append a suffix
modifier. Geographical (degrees) coordinates: Append m to
indicate arc minutes or c to indicate arc seconds. If one of the units e, k, i,
or n is appended instead, the increment is assumed to be given in meter, km, miles, or
nautical miles, respectively, and will be converted to the equivalent degrees longitude at
the middle latitude of the region (the conversion depends on ELLIPSOID). If /y_inc is given but set to 0 it will be reset equal to
x_inc; otherwise it will be converted to degrees latitude.
All coordinates: If = is appended then
the corresponding max x (east) or y (north) may be slightly adjusted to fit exactly the given increment
[by default the increment may be adjusted slightly to fit the given domain]. Finally, instead
of giving an increment you may specify the number of nodes desired by appending + to
the supplied integer argument; the increment is then recalculated from the number of nodes and the domain.
The resulting increment value depends on whether you have selected a gridline-registered
or pixel-registered grid; see Appendix B for details. Note: if -Rgrdfile is used then
grid spacing has already been initialized; use -I to override the values.
west, east, south, and north specify the Region of interest, and you may specify them
in decimal degrees or in [+-]dd:mm[:ss.xxx][W|E|S|N] format. Append r if lower left and upper right
map coordinates are given instead of w/e/s/n. The two shorthands -Rg and -Rd stand for global domain
(0/360 and -180/+180 in longitude respectively, with -90/+90 in latitude). Alternatively, specify the name
of an existing grid file and the -R settings (and grid spacing, if applicable) are copied from the grid.
Features with an area smaller than min_area in km^2 or of hierarchical level
that is lower than min_level or higher than max_level
will not be plotted [Default is 0/0/4 (all features)]. Level 2 (lakes) contains
regular lakes and wide river bodies which we normally include as lakes;
append +r to just get river-lakes or +l to just get regular lakes
(requires GSHHS 2.0.1 or higher). Finally, append +ppercent to exclude
polygons whose percentage area of the corresponding full-resolution feature is less
than percent (requires GSHHS 2.0 or higher).
See GSHHS INFORMATION below for more details.
Selects the resolution of the data set to use ((f)ull, (h)igh, (i)ntermediate, (l)ow, or (c)rude). The
resolution drops off by ~80% between data sets. [Default is l]. Append + to automatically select a lower resolution should
the one requested not be available [abort if not found]. Note that because the coastlines differ in details a
node in a mask file using one resolution is not guaranteed to remain inside [or outside] when a different resolution is selected.
Force pixel node registration [Default is gridline registration].
(Node registrations are defined in GMT Cookbook Appendix B on grid file formats.)
Sets the values that will be assigned to nodes. Values can be any number, including the
textstring NaN. Append o to let nodes exactly on feature boundaries be considered outside [Default is inside].
Specify this information using 1 of 2 formats:
[Default is 0/1/0/1/0 (i.e., 0/1)].
Selects verbose mode, which will send progress reports to stderr [Default runs "silently"].
GRID FILE FORMATS
By default GMT writes out grid as single precision floats in a COARDS-complaint netCDF file format.
However, GMT is able to produce grid files in many other commonly used grid file formats and also facilitates so called "packing" of grids,
writing out floating point data as 2- or 4-byte integers. To specify the precision, scale and offset, the user should add the suffix
=id[/scale/offset[/nan]], where id is a two-letter identifier of the grid type and precision, and scale and offset are optional scale factor
and offset to be applied to all grid values, and nan is the value used to indicate missing data.
See grdreformat(1) and Section 4.17 of the GMT Technical Reference and Cookbook for more information.
When writing a netCDF file, the grid is stored by default with the variable name "z". To specify another variable name varname,
append ?varname to the file name. Note that you may need to escape the special meaning of ? in your shell program
by putting a backslash in front of it, or by placing the filename and suffix between quotes or double quotes.
To set all nodes on land to NaN, and nodes over water to 1, using the high resolution data set, do
grdlandmask -R-60/-40/-40/-30 -Dh -i 5m -N 1/NaN -G land_mask.grd -V
To make a 1x1 degree global grid with the hierarchical levels of the nodes based on the low resolution data:
grdlandmask -R 0/360/-90/90 -Dl -I 1 -N 0/1/2/3/4 -G levels.grd -V
The coastline database is GSHHS which is compiled from two sources:
World Vector Shorelines (WVS) and CIA World Data Bank II (WDBII).
In particular, all level-1 polygons (ocean-land boundary) are derived
from the more accurate WVS while all higher level polygons (level 2-4,
representing land/lake, lake/island-in-lake, and island-in-lake/lake-in-island-in-lake boundaries)
are taken from WDBII. Much processing has taken place to convert WVS
and WDBII data into usable form for GMT:
assembling closed polygons from line segments, checking for duplicates,
and correcting for crossings between polygons. The area of each polygon
has been determined so that the user may choose not to draw features smaller
than a minimum area (see -A); one may also limit the highest hierarchical
level of polygons to be included (4 is the maximum). The 4 lower-resolution
databases were derived from the full resolution database using the
Douglas-Peucker line-simplification algorithm. The classification of rivers
and borders follow that of the WDBII. See the GMT Cookbook and
Technical Reference Appendix K for further details.
|GMT 4.5.14 ||GRDLANDMASK (1) ||1 Nov 2015 |
Visit the GSP FreeBSD Man Page Interface.
Output converted with manServer 1.07.