This variable specifies the UID to which privileges are dropped at startup. After the
socket at link layer has been opened the privileges are dropped to a specific
uid different from root for security reasons. etter.conf is the only file that
is read with root privs. Be sure that the specified uid has enough privs to read other files (etter.*)
You can bypass this variable by setting the environment variable EC_UID.
The value represents the milliseconds to wait between two consecutive packets
during the initial
ARP scan. You can increment this value to be less aggressive at startup. The
randomized scan plus a high delay can fool some types of ARP scan detectors.
With this variable set, only 3 inital poisoned ARP messages are sent to the
victims. This poisoned status is kept up by ettercap with responding to ARP
requests from victims that want to refresh their ARP cache. This makes the
ARP poisoning very stealthy but may be unreliable on shared media such as
When the poisoning process starts, the inter-packet delay is low for the first
5 poisons (to be sure the poisoning process has been successful). After the
first 5 poisons, the delay is incremented (to keep up the poisoning). This
variable controls the delay for the first 5 poisons. The value is in seconds.
The same delay is used when the victims are restored to the original associations (RE-ARPing) when ettercap is closed.
This variable controls the poisoning delay after the first 5 poisons. The
value is expressed in seconds. You can increase this value (to try to fool the
IDS) up to the timeout of the ARP cache (which depends on the poisoned operating system).
Enable the sending of a spoofed ICMP message to force the targets to make an
arp request. This will create an arp entry in the host cache, so ettercap
will be able to win the race condition and poison the target. Useful against
targets that do not accept gratuitous arp if the entry is not in the cache.
Use ARP replies to poison the targets. This is the classic attack.
Use ARP request to poison the targets. Useful against targets that cache even
arp request values.
Set this option to 0 if you want to skip the poisoning of two hosts with the
same mac address. This may happen if a NIC has one or more aliases on the same
This is the lease time (in seconds) for a dhcp assignment. You can lower this
value to permit the victims to receive a correct dhcp reply after you have
stopped your attack. Using higher timeouts can seriously mess up your network after
the attack has finished. On the other hand some clients will prefer a higher lease
time, so you have to increase it to win the race condition against the real
This is the delay time (in milliseconds) between stealing packets for the
"port" mitm method. With low delays you will be able to intercept more
packets, but you will generate more traffic. You have to tune this value
in order to find a good balance between
the number of intercepted packets, re-transmitted packets and lost packets.
This value depends on full/half duplex channels, network drivers and adapters,
network general configuration and hardware.
This is the delay time (in microseconds) between packets when the
"port" mitm method has to re-send packets queues. As said for port_steal_delay
you have to tune this option to the lowest acceptable value.
This option operates similar to the arp_poison_warm_up option.
When the poisoning process starts, this option controls the NDP poison delay
for the first 5 poisons (to be sure the poisoning process has been successful).
After the first 5 poisons, the delay is incremented (to keep up the poisoning).
This variable controls the delay for the first 5 poisons. The value should be
lower than the ndp_poison_delay. The value is in seconds.
The same delay is used when the victims are restored to the original associations
when ettercap is closed.
This option is similar to the arp_poison_delay option.
It controls the delay in seconds for sending out the poisoned NDP packets to
poison victims neighbor cache. This value may be increased to hide from IDSs.
But increasing the value increases as well the probability for failing race
conditions during neighbor discovery and to miss some packets.
This option controls the delay in microseconds between poisoned NDP packets are
sent. This value may be increased to hide from IDSs. But increasing the value
increases as well the probability for failing race conditions during neighbor
discovery and to miss some packets.
Enable the sending of a spoofed ICMPv6 message to motivate the targets to
perform neighbor discovery. This will create an entry in the host neighbor
cache, so ettercap will be able to win the race condition and poison the
target. Useful against targets that do not accept neighbor advertisements
if the entry is not in the cache.
Set this option to 0 if you want to skip the NDP poisoning of two hosts with the
same mac address. This may happen if a NIC has one or more aliases on the same
This option defines the time in seconds ettercap waits for active IPv6 nodes
to respond to the ICMP probes. Decreasing this value could lead to miss replies
from active IPv6 nodes, hence miss them in the host list. Increasing the value
usually has no impact; normally nodes can manage to answer during the default
NOTE: The ndp and icmp6 options are only available if ettercap has been built with IPv6 support
Every time a new connection is discovered, ettercap allocates the needed
structures. After a customizable timeout, you can free these structures to keep
the memory usage low. This variable represents this timeout. The value is
expressed in seconds. This timeout is applied even to the session tracking
system (the protocol state machine for dissectors).
The number of seconds to wait before a connection is marked as IDLE.
This variable controls the size of the buffer linked to each connection.
Every sniffed packet is added to the buffer and when the buffer is full the
older packets are deleted to make room for newer ones. This buffer is useful
to view data that went on the cable before you select and view a specific
connection. The higher this value, the higher the ettercap memory occupation.
By the way, the buffer is dynamic, so if you set a buffer of 100.000 byte it is not
allocated all together at the first packet of a connection, but it is filled as
The timeout in seconds when using the connect() syscall. Increase it if you get
a "Connection timeout" error. This option has nothing to do with connections
sniffed by ettercap. It is a timeout for the connections made by ettercap to
other hosts (for example when fingerprinting remote host).
Ettercap keeps some statistics on the processing time of the bottom half (the
sniffer) and top half (the protocol decoder). These statistics are made on the
average processing time of sampling_rate packets. You can decrease this value to have
a more accurate real-time picture of processing time or increase it to have a
smoother picture. The total average will not change, but the worst value will
be heavily influenced by this value.
When reading from a dump file and using console or daemon UI, this variable is
used to determine what action has to be done on EOF. It is a boolean value. If
set to 1 ettercap will close itself (useful in scripts). Otherwise the session will
continue waiting for user input.
Ettercap collects in memory a profile for each host it detects. Users and
passwords are collected there. If you want to run ettercap in background
logging all the traffic, you may want to disable the collecting in memory to
save system memory. Set this option to 0 (zero) to disable profiles collection.
A value of 1 will enable collection for all the hosts, 2 will collect only
local hosts and 3 only remote hosts (a host is considered remote if it does
not belong to the netmask).
Some dissectors (such as SSH and HTTPS) need to modify the payload of the
packets in order to collect passwords and perform a decryption attack. If you
want to disable the "dangerous" dissectors all together, set this value to 0.
If you set this value to 0 you will sniff even packets forwarded by ettercap
or by the kernel. It will generate duplicate packets in conjunction with the
arp mitm method (for example). It could be useful while running ettercap
in unoffensive mode on a host with more than one network interface
(waiting for the multiple-interface feature...)
If you set the value to 0 the messages about incorrect checksums will not be
displayed in the user messages windows (nor logged to a file with -m).
Note that this option will not disable the check on the packets, but only prevent the message to be displayed (see below).
This option is used to completely disable the check on the checksum of the
packets that ettercap receives. The check on the packets is performed to avoid
ettercap spotting thru bad checsum packets (see Phrack 60.12). If you disable
the check, you will be able to sniff even bad checksummed packet, but you will
be spotted if someone is searching for you...
This value represents the port on which the protocol dissector has to be bound. A
value of 0 will disable the dissector. The name of the variable is the same of
the protocol name. You can specify a non standard port for each dissector as well
as multiple ports. The syntax for multiport selection is the following:
NOTE: some dissectors are conditionally compiled . This means that depending on the libraries found in your system some dissectors will be enabled and some others will not. By default etter.conf contains all supported dissectors. if you got a "FATAL: Dissector "xxx" does not exists (etter.conf line yy)" error, you have to comment out the yy line in etter.conf.
You can customize the colors of the curses GUI.
Simply set a field to one of the following values and look at the GUI aspect :)
Here is a list of values: 0 Black, 1 Red, 2 Green, 3 Yellow, 4 Blue, 5 Magenta, 6 Cyan, 7 White
specifies the encoding to be used while displaying the packets in UTF-8 format.
Use the iconv --list command for a list of supported encodings.
This command is executed by the remote_browser plugin each time it catches a
good URL request into an HTTP connection.
The command should be able to get 2 parameters:
You must provide a valid command (or script) to enable tcp redirection at the
kernel level in order to be able to use SSL dissection. Your script should be
able to get 3 parameters:
This script is used to remove the redirect rules applied by redir_command_on.
You should note that this script is called atexit() and thus it has not high
privileges. You should provide a setuid program or set ec_uid to 0 in order to
be sure that the script is executed successfully.
Alberto Ornaghi (ALoR) <firstname.lastname@example.org>
Marco Valleri (NaGA) <email@example.com>
Emilio Escobar (exfil) <firstname.lastname@example.org>
Eric Milam (Brav0Hax) <email@example.com>
Mike Ryan (justfalter) <firstname.lastname@example.org>
Gianfranco Costamagna (LocutusOfBorg) <email@example.com>
Antonio Collarino (sniper) <firstname.lastname@example.org>
Ryan Linn <email@example.com>
Jacob Baines <firstname.lastname@example.org>
Dhiru Kholia (kholia) <email@example.com>
Alexander Koeppe (koeppea) <firstname.lastname@example.org>
Martin Bos (PureHate) <email@example.com>
Gisle Vanem <firstname.lastname@example.org>
Johannes Bauer <JohannesBauer@gmx.de>
Daten (Bryan Schneiders) <email@example.com>
ettercap(8) ettercap_curses(8) ettercap_plugins(8) etterlog(8) etterfilter(8) ettercap-pkexec(8)
|ettercap 0.8.2||ETTER.CONF (5)|