GSP
Quick Navigator

Search Site

Unix VPS
A - Starter
B - Basic
C - Preferred
D - Commercial
MPS - Dedicated
Previous VPSs
* Sign Up! *

Support
Contact Us
Online Help
Handbooks
Domain Status
Man Pages

FAQ
Virtual Servers
Pricing
Billing
Technical

Network
Facilities
Connectivity
Topology Map

Miscellaneous
Server Agreement
Year 2038
Credits
 

USA Flag

 

 

Man Pages


Manual Reference Pages  -  ATMCONFIG (8)

NAME

atmconfig - ATM configuration tool

CONTENTS

Synopsis
Description
     Common Options
     Obtaining Help
     The Ic diag Ss Command
     The Ic natm Ss Command
See Also
Authors

SYNOPSIS

atmconfig [-htv] [command [sub-command [...]]] [options] [arg ...]

DESCRIPTION

The atmconfig tool is used to configure the Netgraph ATM network sub-system.

The command line of atmconfig generally consists of common options followed by a command string, optionally followed by sub-command strings, optional command specific options and command specific arguments. Commands and sub-commands as well as command specific options may be abbreviated as long as there is only one match possible.

    Common Options

The following common options change the overall behaviour of atmconfig:
-h Print a very short usage info and exit.
-t Several show-type commands output a header and then several lines of information. If this option is given, the header is omitted, simplifying the parsing of the output.
-v Be more verbose.

    Obtaining Help

The help command has a number of useful sub-commands.

To get general help use:

To get a list of available commands use:

To get a list of available sub-commands use:

or (if there are deeper levels of sub-commands):

To get a list of options and arguments for a command use: (given that there are no further sub-command levels).

To get a list of common options use:

    The Ic diag Ss Command

The diag command allows the inspection of the ATM interfaces on the local host and the modification of device parameters. Sub-commands are: list (print a list of interfaces), config (print hardware configuration), phy (access PHY chip), stats (print statistics) and vcc (print list of VCCs).
diag list
  This sub-command lists all ATM interfaces in the system. It takes no options or arguments.
diag config [-atm] [-hardware] [device ...]
  This command prints the configuration of ATM interfaces. If no device is given, all devices are listed, otherwise only the specified devices. The option -atm instructs the command to print ATM layer configuration parameters like the number of VCI and VPI bits, whereas the -hardware option requests card specific information like the vendor or the serial number. If none of the options is given, the defaults is to assume -atm .
diag phy print [-numeric] device
  This command prints the PHY registers in a (potential) human comprehensible format. If -numeric is given, the format is hex bytes. Otherwise, textual representation will be printed.
diag phy show [device ...]
  This sub-command prints static information about the PHY device used in the ATM card like the type of the PHY and the media.
diag phy set device reg mask val
  This sub-command allows one to change bits in PHY registers. This should be used with great care. The bits of the given PHY chip register for which the corresponding bit in mask is one are set to the values of the corresponding bits in val. All register bits that have a zero in mask are written back with their original value.
diag phy stats [-clear] device
  Print the PHY statistics for the given device. When the optional -clear is given, the statistics are cleared atomically.
diag vcc [-abr] [-channel] [-traffic] [device]
  Retrieve the list of currently active channels on either all or the specified interfaces. For each channel, the following information is printed depending on the options (default is -channel ).
-abr Print ABR specific traffic parameters: ICR, TBE, NRM, TRM, ADTF, RIF, RDF, CDF.
-channel
  Print basic information: VPI, VCI, AAL, traffic type, MTU and flags.
-traffic
  Print traffic parameters: PCR, SCR, MBS, MCR.
diag stats device
  Print driver specific statistics.

    The Ic natm Ss Command

The natm command is used to change natmip(4) routes on the local host. The sub-commands for the routing table are: add (to add a new route), delete (to delete an existing route) and show (to print the currently installed NATM routes).

natm add dest device vpi vci encaps
 
natm add dest device vpi vci encaps ubr [pcr]
 
natm add dest device vpi vci encaps cbr pcr
 
natm add dest device vpi vci encaps vbr pcr scr mbs
 
natm add dest device vpi vci encaps abr pcr mcr icr tbe nrm trm adtf rif rdf cdf
  Add a new route to the routing table. The destination address (the address on the other end of the link) is given in dest. The device, vpi and vci arguments are the name of the ATM device and the VPI and VCI values for the link. The encaps argument may be either AAL5 or LLC/SNAP both of which specify AAL5 encapsulation, the first one without additional encapsulation, the second one with LLC/SNAP headers. The first two forms of the command add an UBR (unspecified bit rate) channel, where the second form allows the optional specification of a peak cell rate (PCR). The third form adds a CBR (constant bit rate) channel where a PCR must be given. The fourth form adds a VBR (variable bit rate) channel. The arguments are the peak cell rate, the sustainable cell rate and the maximum bursts size. The last form of the command adds an ABR (available bit rate) channel.

natm delete dest
natm delete device vpi vci
  This commands deletes an NATM route. The route may be specified either by the destination address or by the device, vpi and vci triple.


natm show

  List all NATM routes.

SEE ALSO

natm(4), natmip(4), atm(8)

AUTHORS


.An Hartmut Brandt Aq harti@FreeBSD.org
Search for    or go to Top of page |  Section 8 |  Main Index


Powered by GSP Visit the GSP FreeBSD Man Page Interface.
Output converted with manServer 1.07.