Manual Reference Pages - FAXMODEM (8)
faxmodem - dynamically add a modem to a HylaFAX server system
queue-dir ] [
capabilities ] [
-p ] [
-P ] [
faxmodem sends a message to the HylaFAX queuer process
telling it that the specified modem is ready for use and
informing it about its fax-related capabilities.
This is the mechanism by which modems are added in a send-only
Once a modem has been configured its status can be reconfigured
faxmodem can also be used to alter the capabilities and usage priority
of a previously configured modem.
modem is either the terminal device name where the modem is
attached or a HylaFAX device identifier (see
for information on device identifiers).
Device names may be given without
a leading directory pathname; e.g. ttyf2 instead of /dev/ttyf2.
To figure out the capabilities of a modem either use the
script or manually communicate with the modem.
For a Class 2 modem the capabilities are given in the response to
the AT+FDCC=? query command and
for a Class 2.0 modem the AT+FCC=? command.
To check if a modem is capable of polled retrieval of documents
use AT+FSP=? for a Class 2.0 modem or AT+FSPL=? for a Class 2 modem;
if 1 is indicated in the response then the modem supports polling.
hyla% cu -l ttyf2
In this case the modem would be added using the command:
/usr/local/sbin/faxmodem -c (0,1),(0-5),(0-2),(0-2),0,0,0,(0-7) ttyf2
(by default polling is assumed to be supported).
Class 1 modems require a different technique.
The host implements most of the fax protocol so all that is needed is
to identify the possible signalling rates the modem supports for
is done with the AT+FTM=? command.
hyla% cu -l ttyf2
In this case the modem supports 2400, 4800, 7200, 9600, 12200, and 14400
bps signalling rates so the modem would be added using:
/usr/local/sbin/faxmodem -c (0,1),(0-5),(0-2),(0-2),(0,1),0,0,(0-7) ttyf2
The following options are available:
Specify the fax capabilities using the syntax defined by
the Class 2 specification:
vr specifies vertical resolution,
br specifies bit rate,
wd specifies page width,
ln specifies page length,
df specifies data compression,
ec specifies error correction,
bf specifies binary file transfer,
st specifies scan time/line;
and each of the above specifications is a range or list
of numbers that defines the exact capabilities of the modem.
For example, the default capabilities are
which specifies the modem is capable of sending and receiving
both low and high resolution facsimile with a variety of page
sizes; supports signalling rates 0-3 (2400 bps through 9600 bps);
supports only 1D-encoded data compression; and does not support
error correction or binary file transfer.
A modems ability to support polled retrieval of facsimile is
specified separately with the
Specify the modem is not capable of polling for remote documents.
Specify the modem is capable of polling for remote documents (default).
-q dir ||
Use a spooling area other than
-u priority ||
Assign the specified priority to the modem when scheduling
it for outbound use.
Modem priorities are numbers in the range [0..255] with lower
numbers meaning higher priority.
Modems are initially assigned priority 255.
/var/spool/hylafax default spooling area
/var/spool/hylafax/FIFO fifo for contacting faxq
for a complete discussion of the structure and
content of the spooling area.
|--> ||FAXMODEM (8C) ||Oct 27, 1995 |
Visit the GSP FreeBSD Man Page Interface.
Output converted with manServer 1.07.